Difference between revisions of "How to Restore Yocto Linux to the eMMC on NX8MM-35"
From ICOP tech wiki
(Created page with "{{#vardefine:RELEASE_PARAM|{{#urlget:release}}}} <!-- --> {{#lst:Yocto_Platform_Customization|{{#var:RELEASE_PARAM|RELEASE_MORTY_V1.0_DART-6UL}}}} <!-- --> {{PageHeader|How to...") |
|||
(11 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
{{#vardefine:RELEASE_PARAM|{{#urlget:release}}}} <!-- | {{#vardefine:RELEASE_PARAM|{{#urlget:release}}}} <!-- | ||
--> {{#lst:Yocto_Platform_Customization|{{#var:RELEASE_PARAM|RELEASE_MORTY_V1.0_DART-6UL}}}} <!-- | --> {{#lst:Yocto_Platform_Customization|{{#var:RELEASE_PARAM|RELEASE_MORTY_V1.0_DART-6UL}}}} <!-- | ||
− | --> {{PageHeader|How to Restore Yocto Linux to the eMMC on | + | --> {{PageHeader|How to Restore Yocto Linux to the eMMC on NX8MM-35}} |
− | + | ==<big>Restore the Yocto Linux via Linux host PC to the NX8MM-35</big>== | |
− | ==Restore the Yocto Linux via Linux host PC to the | ||
===Tools you need before restoring the image to the eMMC:=== | ===Tools you need before restoring the image to the eMMC:=== | ||
*<u>Recovery image</u> with the <u>UUU burning software</u>: | *<u>Recovery image</u> with the <u>UUU burning software</u>: | ||
− | ** | + | **Display: HDMI |
+ | ***2GB RAM version:https://ftp.icop.com.tw/share/n3Ao-zi7 | ||
*A 64-bit Linux host O/S on a PC (The virtual machine is not suggested to be used) | *A 64-bit Linux host O/S on a PC (The virtual machine is not suggested to be used) | ||
− | *USB cable | + | *USB cable to connect between the host PC and the NX8MM-35. (Ex: USB to micro USB) |
− | ===Write the image to the eMMC on the | + | ===Write the image to the eMMC on the NX8MM-35.=== |
− | |||
− | *Find the SW1 | + | *This section will introduce how to write the image to the eMMC on the NX8MM-35 step by step. |
+ | *Find the SW1 on the NX8MM-35 and change the setting to Serial Download Mode according to the photo below: | ||
− | [[File: | + | [[File:NX8MM-35 JP.jpg|alt=|frameless|300x300px]] |
*Turn on the host PC and unzip the image file in it. | *Turn on the host PC and unzip the image file in it. | ||
− | *Connect the USB | + | *Connect the USB to micro USB to the host PC, but not connect to the NX8MM-35. |
− | + | *Open a terminal on the host PC and access the location you’ve put the image file and input "sudo chmod a+x uuu" to enable uuu as executable command. | |
− | + | *Input “sudo ./uuu xxxx.auto” (check the xxxx.auto name in the file) ; you will see “Wait for known USB Device Appear” | |
− | |||
− | *Open a terminal on the host PC and access the location you’ve put the image file and input “sudo ./uuu | ||
− | |||
− | |||
− | |||
− | |||
− | [[File:Yocto | + | [[File:Nx8mm-35 Yocto-1.2.5.png|alt=|frameless|680x680px]] |
+ | *Connect the Micro USB to the NX8MM-35, and it will trigger the serial download mode to restore the image from the host PC. | ||
*After the restore process is done, it will show on the host PC as the image below: | *After the restore process is done, it will show on the host PC as the image below: | ||
− | [[File: | + | [[File:Nx8mm-35Yocto-1.2.7.png|alt=|frameless|680x680px]] |
− | *Remove the | + | *Remove the USB to Micro USB cable on the NX8MM-35(Power off), and set the SW1 to Internal boot as below. |
− | [[File: | + | [[File:NX8MM-35 JP2.jpg|alt=|frameless|300x300px]] |
− | *Power on the | + | *Power on the NX8MM-35 and you can see the Yocto Linux booting. |
[[File:1-2-11.png|frameless|480x480px]] | [[File:1-2-11.png|frameless|480x480px]] | ||
− | |||
− | |||
− | |||
− | |||
<br /> | <br /> | ||
− | ==Restore the Yocto Linux via Win10 host PC to the | + | ==<big>Restore the Yocto Linux via Win10 host PC to the NX8MM-35.</big>== |
===Tools you need before restoring the image to the eMMC:=== | ===Tools you need before restoring the image to the eMMC:=== | ||
− | * | + | *<u>Recovery image</u> with the <u>UUU burning software</u>: |
− | ** | + | **Display: HDMI |
+ | ***2GB RAM version:https://ftp.icop.com.tw/share/n3Ao-zi7 | ||
*A Windows 10 host O/S on a PC (The virtual machine is not suggested to be used) | *A Windows 10 host O/S on a PC (The virtual machine is not suggested to be used) | ||
− | *USB cable | + | *USB cable to connect between the host PC and NX8MM-35.(Ex: USB to micro USB) |
− | ===Write the image to the eMMC on the | + | ===Write the image to the eMMC on the NX8MM-35.=== |
− | This section will introduce how to write the image to the eMMC on the | + | This section will introduce how to write the image to the eMMC on the NX8MM-35 step by step. |
− | *Find the SW1 | + | *Find the SW1 on the NX8MM-35 and change the setting to Serial Download Mode according to the photo below: |
− | [[File: | + | [[File:NX8MM-35 JP.jpg|alt=|frameless|300x300px]] |
*Turn on the host PC and unzip the image file to it. | *Turn on the host PC and unzip the image file to it. | ||
− | *Connect the USB | + | *Connect the USB to micro USB cable to the host PC, but not connect to NX8MM-35. |
− | |||
− | |||
− | |||
*Open a terminal on the host PC and access the location you’ve put the image file and input “uuu.exe uuu.auto” , and you will see “Wait for known USB Device Appear”. | *Open a terminal on the host PC and access the location you’ve put the image file and input “uuu.exe uuu.auto” , and you will see “Wait for known USB Device Appear”. | ||
− | [[File: | + | [[File:NX8MM YOCTO IMAGE1 windows.jpg|alt=|frameless|690x690px]] |
− | |||
− | |||
− | |||
− | |||
+ | *Connect the Micro USB to the NX8MM-35, and it will trigger the serial download mode to restore the image from the host PC. | ||
*After the restore process is done, it will show on the host PC as the image below: | *After the restore process is done, it will show on the host PC as the image below: | ||
− | [[File:Yocto | + | [[File:NX8MM-35 Yocto IMAGE2 windows.jpg|alt=|frameless|800x800px]] |
− | *Remove the | + | *Remove the USB to Micro USB cable on the NX8MM-35(Power off), and set the SW1 to Internal boot as below. |
− | [[File: | + | [[File:NX8MM-35 JP2.jpg|alt=|frameless|300x300px]] |
− | *Power on the | + | *Power on the NX8MM-35 and you can see the Yocto Linux booting. |
− | [[File:1-2-11.png|frameless| | + | [[File:1-2-11.png|frameless|480x480px]] |
− | + | <br /> | |
− | + | <br /> |
Latest revision as of 20:52, 27 December 2023
How to Restore Yocto Linux to the eMMC on NX8MM-35
Contents
Restore the Yocto Linux via Linux host PC to the NX8MM-35
Tools you need before restoring the image to the eMMC:
- Recovery image with the UUU burning software:
- Display: HDMI
- 2GB RAM version:https://ftp.icop.com.tw/share/n3Ao-zi7
- Display: HDMI
- A 64-bit Linux host O/S on a PC (The virtual machine is not suggested to be used)
- USB cable to connect between the host PC and the NX8MM-35. (Ex: USB to micro USB)
Write the image to the eMMC on the NX8MM-35.
- This section will introduce how to write the image to the eMMC on the NX8MM-35 step by step.
- Find the SW1 on the NX8MM-35 and change the setting to Serial Download Mode according to the photo below:
- Turn on the host PC and unzip the image file in it.
- Connect the USB to micro USB to the host PC, but not connect to the NX8MM-35.
- Open a terminal on the host PC and access the location you’ve put the image file and input "sudo chmod a+x uuu" to enable uuu as executable command.
- Input “sudo ./uuu xxxx.auto” (check the xxxx.auto name in the file) ; you will see “Wait for known USB Device Appear”
- Connect the Micro USB to the NX8MM-35, and it will trigger the serial download mode to restore the image from the host PC.
- After the restore process is done, it will show on the host PC as the image below:
- Remove the USB to Micro USB cable on the NX8MM-35(Power off), and set the SW1 to Internal boot as below.
- Power on the NX8MM-35 and you can see the Yocto Linux booting.
Restore the Yocto Linux via Win10 host PC to the NX8MM-35.
Tools you need before restoring the image to the eMMC:
- Recovery image with the UUU burning software:
- Display: HDMI
- 2GB RAM version:https://ftp.icop.com.tw/share/n3Ao-zi7
- Display: HDMI
- A Windows 10 host O/S on a PC (The virtual machine is not suggested to be used)
- USB cable to connect between the host PC and NX8MM-35.(Ex: USB to micro USB)
Write the image to the eMMC on the NX8MM-35.
This section will introduce how to write the image to the eMMC on the NX8MM-35 step by step.
- Find the SW1 on the NX8MM-35 and change the setting to Serial Download Mode according to the photo below:
- Turn on the host PC and unzip the image file to it.
- Connect the USB to micro USB cable to the host PC, but not connect to NX8MM-35.
- Open a terminal on the host PC and access the location you’ve put the image file and input “uuu.exe uuu.auto” , and you will see “Wait for known USB Device Appear”.
- Connect the Micro USB to the NX8MM-35, and it will trigger the serial download mode to restore the image from the host PC.
- After the restore process is done, it will show on the host PC as the image below:
- Remove the USB to Micro USB cable on the NX8MM-35(Power off), and set the SW1 to Internal boot as below.
- Power on the NX8MM-35 and you can see the Yocto Linux booting.