Difference between revisions of "How to Restore Yocto Linux 3.3 to the eMMC on NX8MM-35"
From ICOP tech wiki
Line 1: | Line 1: | ||
{{#vardefine:RELEASE_PARAM|{{#urlget:release}}}} <!-- | {{#vardefine:RELEASE_PARAM|{{#urlget:release}}}} <!-- | ||
--> {{#lst:Yocto_Platform_Customization|{{#var:RELEASE_PARAM|RELEASE_MORTY_V1.0_DART-6UL}}}} <!-- | --> {{#lst:Yocto_Platform_Customization|{{#var:RELEASE_PARAM|RELEASE_MORTY_V1.0_DART-6UL}}}} <!-- | ||
− | --> {{PageHeader|How to Restore Yocto Linux 3.3 to the eMMC on | + | --> {{PageHeader|How to Restore Yocto Linux 3.3 to the eMMC on NX8MM-35}} |
==<big>Restore the Yocto Linux 3.3 via Linux host PC to the NX8MM-35</big>== | ==<big>Restore the Yocto Linux 3.3 via Linux host PC to the NX8MM-35</big>== | ||
===Tools you need before restoring the image to the eMMC:=== | ===Tools you need before restoring the image to the eMMC:=== | ||
Line 16: | Line 16: | ||
*Find the SW1 on the NX8MM-35 and change the setting to Serial Download Mode according to the photo below: | *Find the SW1 on the NX8MM-35 and change the setting to Serial Download Mode according to the photo below: | ||
− | [[File: | + | [[File:NX8MM-35 JP.jpg|alt=|frameless|335x335px]] |
*Turn on the host PC and unzip the image file in it. | *Turn on the host PC and unzip the image file in it. | ||
Line 27: | Line 27: | ||
*Remove the USB to Micro USB cable on the NX8MM-35 (Power off), and set the SW1 to Internal boot as below. | *Remove the USB to Micro USB cable on the NX8MM-35 (Power off), and set the SW1 to Internal boot as below. | ||
− | [[File: | + | [[File:NX8MM-35 JP2.jpg|alt=|frameless|330x330px]] |
*Power on the NX8MM-35 and you can see the Yocto Linux booting. | *Power on the NX8MM-35 and you can see the Yocto Linux booting. | ||
Line 49: | Line 49: | ||
*Find the SW1 on the NX8MM-35 and change the setting to Serial Download Mode according to the photo below: | *Find the SW1 on the NX8MM-35 and change the setting to Serial Download Mode according to the photo below: | ||
− | [[File: | + | [[File:NX8MM-35 JP.jpg|alt=|frameless|329x329px]] |
*Turn on the host PC and unzip the image file to it. | *Turn on the host PC and unzip the image file to it. | ||
Line 60: | Line 60: | ||
*Remove the USB to Micro USB cable on the NX8MM-35 (Power off), and set the SW1 to Internal boot as below. | *Remove the USB to Micro USB cable on the NX8MM-35 (Power off), and set the SW1 to Internal boot as below. | ||
− | [[File: | + | [[File:NX8MM-35 JP2.jpg|alt=|frameless|322x322px]] |
*Power on the NX8MM-35 and you can see the Yocto Linux booting. | *Power on the NX8MM-35 and you can see the Yocto Linux booting. |
Revision as of 16:58, 22 June 2022
How to Restore Yocto Linux 3.3 to the eMMC on NX8MM-35
Contents
Restore the Yocto Linux 3.3 via Linux host PC to the NX8MM-35
Tools you need before restoring the image to the eMMC:
- Recovery image with the UUU burning software:
- 2GB RAM version:https://ftp.icop.com.tw/share/aSNZLrOD
- A 64-bit Linux host O/S on a PC (The virtual machine is not suggested to be used)
- USB cable to connect between the host PC and the NX8MM-35. (Ex: USB to micro USB)
Write the image to the eMMC on the NX8MM-35.
- This section will introduce how to write the image to the eMMC on the NX8MM-35 step by step.
- Find the SW1 on the NX8MM-35 and change the setting to Serial Download Mode according to the photo below:
- Turn on the host PC and unzip the image file in it.
- Connect the USB to micro USB to the host PC, but not connect to the NX8MM-35.
- Open a terminal on the host PC and access the location you’ve put the image file and input “sudo ./uuu uuu.auto” ; you will see “Wait for known USB Device Appear”
- Connect the Micro USB to the NX8MM-35, and it will trigger the serial download mode to restore the image from the host PC.
- Wait After the restore process is done.
- Remove the USB to Micro USB cable on the NX8MM-35 (Power off), and set the SW1 to Internal boot as below.
- Power on the NX8MM-35 and you can see the Yocto Linux booting.
Restore the Yocto Linux 3.3 via Win10 host PC to the NX8MM-35.
Tools you need before restoring the image to the eMMC:
- Recovery image with the UUU burning software:
- 2GB RAM version:https://ftp.icop.com.tw/share/aSNZLrOD
- A Windows 10 host O/S on a PC (The virtual machine is not suggested to be used)
- USB cable to connect between the host PC and NX8MM-35.(Ex: USB to micro USB)
Write the image to the eMMC on the NX8MM-35.
This section will introduce how to write the image to the eMMC on the NX8MM-35 step by step.
- Find the SW1 on the NX8MM-35 and change the setting to Serial Download Mode according to the photo below:
- Turn on the host PC and unzip the image file to it.
- Connect the USB to micro USB cable to the host PC, but not connect to NX8MM-35.
- Open a terminal on the host PC and access the location you’ve put the image file and input “uuu.exe uuu.auto” , and you will see “Wait for known USB Device Appear”.
- Connect the Micro USB to the NX8MM-35, and it will trigger the serial download mode to restore the image from the host PC.
- Wait After the restore process is done.
- Remove the USB to Micro USB cable on the NX8MM-35 (Power off), and set the SW1 to Internal boot as below.
- Power on the NX8MM-35 and you can see the Yocto Linux booting.